Diamond segments incorporate small-size diamonds and sheet metal bond materials. The metal bond materials may add powders of Cu, Sn, Fe, Ag, Corp, Ni, WC, Mo, graphite, or anything else. The diamonds are mixed with the bond materials, and the particular mixture is loaded in molds. After hot important or cold pressing, sintering, along with arc grinding, diamond messages are formed. The sheet metal bond has two basic functions: One is bonding the diamonds to the body of the program; the other is wearing combined with diamonds' wearing to let the revolutionary sharp diamonds be uncovered properly.
Generally, a diamond segment carries a working layer and any transition layer. The operating layer contains diamond grains with regard to cutting or grinding, insurance policy coverage transition layer has very little diamonds. It just contains bond materials, and can be used to connect the working layer towards body of the diamond tool. The transition layer is critical for diamond segments utilized on laser-welded diamond tools. The compositions belonging to the two layers should not be varies greatly. Otherwise, the junction of them will tend to break due to the uneven heat and forces received because of the two layers when the diamond tool was in use.
The diamond segments come with large diamond circular discovered blades or diamond gang saws for cutting stones is often layered and have a great deal of non-working layers separating the actual working layers. The working layers contain more common materials of diamond sections, including diamonds and sheet metal bonding materials, while the non-working layers are often made of metal powders. This design can enhance the sharpness of the gemstone segment, and lower its production cost.
The features of the diamond segments using a diamond tool should match the nature of the material to be slice. If the material is usually hard, the bond in the diamond segments should possibly be softer. Because diamonds are more likely to become blunt when cutting hard material. The softer bond is usually worn down with the actual blunt diamonds faster, after which you can make new diamonds beneath be more easily exposed to be involved in cutting. If the content is relatively softer, the bond should be harder. For in this case diamonds can be preserved longer. The harder bond dons slower, so that it can hold the diamonds in addition longer. This can make better technique diamonds and prolong that diamond tool's service lifestyle.
The grit (size), hardness and concentration of the diamonds in the diamond segments should also be considered. For case, when the material to be cut is soft, the diamonds' size may be big, hardness can possibly be medium, and concentration should be a bit more higher. This combination could possibly get good cutting efficiency, and together prolong the blade's existence. When the material is actually hard, the diamonds' size should be small, hardness should always be high, and concentration might be a little bit lower.
https://www.singoon.com/Diamond-Segment-pl3421452.html
Generally, a diamond segment carries a working layer and any transition layer. The operating layer contains diamond grains with regard to cutting or grinding, insurance policy coverage transition layer has very little diamonds. It just contains bond materials, and can be used to connect the working layer towards body of the diamond tool. The transition layer is critical for diamond segments utilized on laser-welded diamond tools. The compositions belonging to the two layers should not be varies greatly. Otherwise, the junction of them will tend to break due to the uneven heat and forces received because of the two layers when the diamond tool was in use.
The diamond segments come with large diamond circular discovered blades or diamond gang saws for cutting stones is often layered and have a great deal of non-working layers separating the actual working layers. The working layers contain more common materials of diamond sections, including diamonds and sheet metal bonding materials, while the non-working layers are often made of metal powders. This design can enhance the sharpness of the gemstone segment, and lower its production cost.
The features of the diamond segments using a diamond tool should match the nature of the material to be slice. If the material is usually hard, the bond in the diamond segments should possibly be softer. Because diamonds are more likely to become blunt when cutting hard material. The softer bond is usually worn down with the actual blunt diamonds faster, after which you can make new diamonds beneath be more easily exposed to be involved in cutting. If the content is relatively softer, the bond should be harder. For in this case diamonds can be preserved longer. The harder bond dons slower, so that it can hold the diamonds in addition longer. This can make better technique diamonds and prolong that diamond tool's service lifestyle.
The grit (size), hardness and concentration of the diamonds in the diamond segments should also be considered. For case, when the material to be cut is soft, the diamonds' size may be big, hardness can possibly be medium, and concentration should be a bit more higher. This combination could possibly get good cutting efficiency, and together prolong the blade's existence. When the material is actually hard, the diamonds' size should be small, hardness should always be high, and concentration might be a little bit lower.
https://www.singoon.com/Diamond-Segment-pl3421452.html
Diamond segments incorporate small-size diamonds and sheet metal bond materials. The metal bond materials may add powders of Cu, Sn, Fe, Ag, Corp, Ni, WC, Mo, graphite, or anything else. The diamonds are mixed with the bond materials, and the particular mixture is loaded in molds. After hot important or cold pressing, sintering, along with arc grinding, diamond messages are formed. The sheet metal bond has two basic functions: One is bonding the diamonds to the body of the program; the other is wearing combined with diamonds' wearing to let the revolutionary sharp diamonds be uncovered properly.
Generally, a diamond segment carries a working layer and any transition layer. The operating layer contains diamond grains with regard to cutting or grinding, insurance policy coverage transition layer has very little diamonds. It just contains bond materials, and can be used to connect the working layer towards body of the diamond tool. The transition layer is critical for diamond segments utilized on laser-welded diamond tools. The compositions belonging to the two layers should not be varies greatly. Otherwise, the junction of them will tend to break due to the uneven heat and forces received because of the two layers when the diamond tool was in use.
The diamond segments come with large diamond circular discovered blades or diamond gang saws for cutting stones is often layered and have a great deal of non-working layers separating the actual working layers. The working layers contain more common materials of diamond sections, including diamonds and sheet metal bonding materials, while the non-working layers are often made of metal powders. This design can enhance the sharpness of the gemstone segment, and lower its production cost.
The features of the diamond segments using a diamond tool should match the nature of the material to be slice. If the material is usually hard, the bond in the diamond segments should possibly be softer. Because diamonds are more likely to become blunt when cutting hard material. The softer bond is usually worn down with the actual blunt diamonds faster, after which you can make new diamonds beneath be more easily exposed to be involved in cutting. If the content is relatively softer, the bond should be harder. For in this case diamonds can be preserved longer. The harder bond dons slower, so that it can hold the diamonds in addition longer. This can make better technique diamonds and prolong that diamond tool's service lifestyle.
The grit (size), hardness and concentration of the diamonds in the diamond segments should also be considered. For case, when the material to be cut is soft, the diamonds' size may be big, hardness can possibly be medium, and concentration should be a bit more higher. This combination could possibly get good cutting efficiency, and together prolong the blade's existence. When the material is actually hard, the diamonds' size should be small, hardness should always be high, and concentration might be a little bit lower.
https://www.singoon.com/Diamond-Segment-pl3421452.html
0 Comments
0 Shares